TECHNICAL DETAILS: • Super strength steel. • DP cutting edge. • HW plunging tip for diagonal plunge-cutting (Z-axis tool entrance). • Resharpenable cutter (max 3 times). • Max feed speed 5 m/min.

TECHNICAL DETAILS: • Super strength steel. • DP cutting edge. • HW plunging tip for diagonal plunge-cutting (Z-axis tool entrance). • Resharpenable cutter (max 3 times). • Max feed speed 5 m/min.

The new CMT One-Piece Rail and Stile Bit represents the union of two cutters in one bit. By simply adjusting the height of the bit, you can cut two perfectly joining profiles with no wasted time or effort moving the fence or changing the...

These bits are designed for those special projects that require a smaller panel door. Use these bits with stock from 11,1mm to 17,4mm thick, and build doors as small as 70mm.  

Designed for fine furniture construction, these bits mill a delicate 4,75mm thumbnail profile in stock from 15,8mm to 20,6mm.  

The CMT male-female rail and stile sets are a perfect pair for this particular project and produce clean, precise and well-crafted joints. Designed for working in stock from 18mm to 22mm.    Shop tips: quality workmanship is the result of a lot of trial...

The CMT male-female rail and stile sets are a perfect pair for this particular project and produce clean, precise and well-crafted joints. Designed for working in stock from 18mm to 22mm.    Shop tips: quality workmanship is the result of a lot of trial...

The CMT male-female rail and stile sets are a perfect pair for this particular project and produce clean, precise and well-crafted joints. Designed for working in stock from 18mm to 22mm.    Shop tips: quality workmanship is the result of a lot of trial...

Use a sturdy 90° angle fence on your router table along with routers with a minimum speed of 1,7 KW (2-1/4 HP). Routers as low-powered as 1,1 KW (1-1/2 HP) can be used but we suggest limiting their use to shorter, shallower runs.  ...

Use a sturdy 90° angle fence on your router table along with routers with a minimum speed of 1,7 KW (2-1/4 HP). Routers as low-powered as 1,1 KW (1-1/2 HP) can be used but we suggest limiting their use to shorter, shallower runs.  ...

Use a sturdy 90° angle fence on your router table along with routers with a minimum speed of 1,7 KW (2-1/4 HP). Routers as low-powered as 1,1 KW (1-1/2 HP) can be used but we suggest limiting their use to shorter, shallower runs.  ...

These bits has a back-cutter which allows milling of both the front and back of the panel in the same cut. An additional 31,7mm (1-1/4") diameter bearing promotes safety by allowing you to take two shallow passes by using the Ø89mm (3-1/2") bit only.

Round Nose bits are a basic curved bit often used for sign making. The round nose is perfect for cutting round grooves in any project without leaving square corners. Materials: Natural woods, composite woods, hard plastics, thin aluminum Recommended RPM: 16,000-18,000 (max 24,000)

These bits has a back-cutter which allows milling of both the front and back of the panel in the same cut. An additional 31,7mm (1-1/4") diameter bearing promotes safety by allowing you to take two shallow passes by using the Ø89mm (3-1/2") bit only.

These bits has a back-cutter which allows milling of both the front and back of the panel in the same cut. An additional 31,7mm (1-1/4") diameter bearing promotes safety by allowing you to take two shallow passes by using the Ø89mm (3-1/2") bit only.

These bits has a back-cutter which allows milling of both the front and back of the panel in the same cut. An additional 31,7mm (1-1/4") diameter bearing promotes safety by allowing you to take two shallow passes by using the Ø89mm (3-1/2") bit only.

Make classic raised panel doors by choosing from the profiles illustrated below. Its anti-kickback design is fundamental in further improving safety when working with larger diameter bits.   Safety Tips: This type of bit needs to be used at a lower rotational speed, preferably...

Make classic raised panel doors by choosing from the profiles illustrated below. Its anti-kickback design is fundamental in further improving safety when working with larger diameter bits.   Safety Tips: This type of bit needs to be used at a lower rotational speed, preferably...

Make classic raised panel doors by choosing from the profiles illustrated below. Its anti-kickback design is fundamental in further improving safety when working with larger diameter bits.   Safety Tips: This type of bit needs to be used at a lower rotational speed, preferably...

Make classic raised panel doors by choosing from the profiles illustrated below. Its anti-kickback design is fundamental in further improving safety when working with larger diameter bits.   Safety Tips: This type of bit needs to be used at a lower rotational speed, preferably...

Make classic raised panel doors by choosing from the profiles illustrated below. Its anti-kickback design is fundamental in further improving safety when working with larger diameter bits.   Safety Tips: This type of bit needs to be used at a lower rotational speed, preferably...

Make classic raised panel doors by choosing from the profiles illustrated below. Its anti-kickback design is fundamental in further improving safety when working with larger diameter bits.   Safety Tips: This type of bit needs to be used at a lower rotational speed, preferably...

Make classic raised panel doors by choosing from the profiles illustrated below. Its anti-kickback design is fundamental in further improving safety when working with larger diameter bits.   Safety Tips: This type of bit needs to be used at a lower rotational speed, preferably...

Make classic raised panel doors by choosing from the profiles illustrated below. Its anti-kickback design is fundamental in further improving safety when working with larger diameter bits.   Safety Tips: This type of bit needs to be used at a lower rotational speed, preferably...

These special carbide-tipped bits work best on solid surfaces or when repairing damaged surfaces. To repair, create the plug with the plug-cutter first, then use the other bit to easily make the hole. Your surfaces will look like new again!

These bits are ideal for making strong joints on any solid surface, thanks to a wider area for glue.

Edge profile bit designed to create a 15° beveled edge on solid surface countertops. Can also be used for European type topmount installation with sinks and bowls. For use on hand-held portable and table routers.  

This bit is ideal for creating custom drainboard patterns in solid surface countertops.   For use on hand-held portable routers.

This bit is ideal for creating custom drainboard patterns in solid surface countertops.   For use on hand-held portable routers.

This bit is designed to create “no-drip” edges on kitchen and vanity counter tops. Designed for hand-held portable routers on applications where a guide bearing cannot be used. This one bit will cut both the outer and inner profiles creating slightly raised edge, controlling...

Trim a sink cut-out flush with the bowl in stages using these "over-hang" and flush trim bits. The Delrin® bearings are tapered to match the slope of the bowl's side. A first pass with the over-hang bit cleans the cut-out edge, leaving a slight...

Trim a sink cut-out flush with the bowl in stages using these "over-hang" and flush trim bits. The Delrin® bearings are tapered to match the slope of the bowl's side. A first pass with the over-hang bit cleans the cut-out edge, leaving a slight...

Trim a sink cut-out flush with the bowl in stages using these "over-hang" and flush trim bits. The Delrin® bearings are tapered to match the slope of the bowl's side. A first pass with the over-hang bit cleans the cut-out edge, leaving a slight...

Trim a sink cut-out flush with the bowl in stages using these "over-hang" and flush trim bits. The Delrin® bearings are tapered to match the slope of the bowl's side. A first pass with the over-hang bit cleans the cut-out edge, leaving a slight...

These bits are designed for undermount applications joining the countertops and sink bowls with a 10 (degree) beveled edge. Can be used with the 880.541.11 and 880.542.11 for complete undermount applications. For use on hand-held routers. Features a non-marring Delrin® bearing to protect the...

These bits roundover and trim the countertop edges after the bowl is mounted. Can be used with the CMT 8/980.551.11 and 8/966.501.11 bevel cutter for a flush cut-out between the countertop and installed undermount bowl. For use on hand-held portable routers. Features a non-marring...

These bits are the best tool for rounding over and trimming countertop edges after the bowl is mounted. Can be used together with the CMT 8/980.551.11 bevel cutter for a flush cut-out between the countertop and the installed undermount bowl. For use on hand-held...

This bit is designed to create “no-drip” edges on kitchen and vanity counter tops in a single pass. For use on hand-held portable routers. This one bit will cut both the outer and inner profiles creating a slightly raised edge that controls spilled liquids....

Create elegant countertops with flawless results. Features a non-marring Delrin® bearing to protect the finished edges.   For use on hand-held portable routers.

Add a decorative wood, plastic or metal inlay to solid surface countertops. Equipped with a non-marring Delrin® bearing to protect the finished edges.   For use on hand-held portable routers.

Add a decorative wood, plastic or metal inlay to solid surface countertops. Equipped with a non-marring Delrin® bearing to protect the finished edges.   For use on hand-held portable routers.

Add a decorative wood, plastic or metal inlay to solid surface countertops. Equipped with a non-marring Delrin® bearing to protect the finished edges.   For use on hand-held portable routers.

Use these bits to create a traditional roundover edge on solid surface countertops. Equipped with a non-marring Delrin® bearing to protect the finished edges.   For use on hand-held portable routers.

Use these bits to create a traditional roundover edge on solid surface countertops. Equipped with a non-marring Delrin® bearing to protect the finished edges.   For use on hand-held portable routers.

Use these bits to create a traditional roundover edge on solid surface countertops. Equipped with a non-marring Delrin® bearing to protect the finished edges.   For use on hand-held portable routers.

Use these bits to create a traditional roundover edge on solid surface countertops. Equipped with a non-marring Delrin® bearing to protect the finished edges.   For use on hand-held portable routers.

Use these bits to create a traditional roundover edge on solid surface countertops. Equipped with a non-marring Delrin® bearing to protect the finished edges.   For use on hand-held portable routers.

These bits can be used for decorative work on solid wood panels and MDF materials. Use them in one pass or in combination with CMT’s MDF panel bits for complex and intricate profiles. A simple approach for an elegant appearance.  Featuring large cutting diameters...

These bits can be used for decorative work on solid wood panels and MDF materials. Use them in one pass or in combination with CMT’s MDF panel bits for complex and intricate profiles. A simple approach for an elegant appearance.  Featuring large cutting diameters...

These bits can be used for decorative work on solid wood panels and MDF materials. Use them in one pass or in combination with CMT’s MDF panel bits for complex and intricate profiles. A simple approach for an elegant appearance.  Featuring large cutting diameters...