DeWalt

A step drill bit for larger holes from 7/8" to 1-1/8" in sheet metal. Titanium nitride coating, designed for impact drivers with a high chip-removal rate.

A step drill bit that drills holes from 3/16" to 7/8" in sheet metal and other thin stock. Titanium nitride coating, a split-point tip and an impact-ready hex shank.

A step drill bit that drills holes from 1/8" to 1/2" in sheet metal and other thin stock. Titanium nitride coating, dual-flute spiral design and a split-point tip, with an impact-ready hex shank.

An 8" 40-tooth carbide-tipped blade for cutting ferrous metal, with a 5/8" arbor. Better carbide for a longer life and less chipping. Kerf: .077".

A 5-1/2" 30-tooth carbide blade for cutting stainless steel, with a 20mm arbor. Carbide teeth are rated by DeWalt for up to 50% longer life. Kerf: .06".

A 6-1/2" 48-tooth carbide-tipped blade for cutting ferrous metal, with a 5/8" arbor. Precise tip placement for accurate cuts and long life. Kerf: .061".

A 14" 90-tooth blade for cutting stainless steel, with a 1" arbor.

A 14" 66-tooth blade for cutting ferrous metal, with a 1" arbor.

A 14" 90-tooth carbide-tipped blade for cutting ferrous metal, with a 1" arbor. DeWalt rates it for up to 50% longer life. Kerf: .091".

A 12" 80-tooth carbide-tipped blade for cutting stainless steel, with a 1" arbor. A stiff plate minimizes run-out and extends blade life. Kerf: .085".

A 4-5/8" heavy-duty self-feed bit in high-carbon steel for boring extra-large holes in timber, with an aggressive spur for fast starts.

A 3-5/8" self-feed bit in high-carbon steel for boring very large holes in timber. The aggressive spur starts the cut fast.

A 3" heavy-duty self-feed bit in high-speed steel, for boring very large holes in timber. An aggressive spur starts the cut fast.

A 2-1/4" self-feed bit for boring large holes in framing lumber.

A 1-1/4" heavy-duty self-feed bit with an aggressive spur for fast penetration. Optimized cutting geometry and an open-tooth design for resharpening.

A 20-piece impact-ready magnetic screwdriving set in a ToughCase.

A 28-piece drill and drive set with Rapid Load bit bars in a ToughCase+. The connectable case system saves storage space, and the bit-bar design lets you remove and swap bits easily.

A 15-pack of Elite Series bit holders with a PH2 Phillips bit, rated for impact drivers and drills. The FlexTorq zone absorbs impact for a longer life.

A 28-piece impact-ready screwdriving set.

A 3-pack of 7-1/4" 24-tooth carbide-tipped circular saw blades for framing and rough cuts in wood, with a body designed to limit binding and burning.

A 2-pack of 7-1/4" 24-tooth carbide-tipped circular saw blades for framing and rough cuts in wood. DeWalt rates them at up to 2x the life, and the body design limits binding and burning.

A 2-pack of 7-1/4" 24-tooth circular saw blades.

A 3-pack of 9" demolition reciprocating blades with welded carbide tips at 6 TPI, for cutting wood, nailed wood and drywall. Blade width: 1".

A 3-pack of 9" Elite Series carbide-tipped reciprocating saw blades at 8 TPI, for demanding demolition and metal cutting.

A 3-pack of 6" demolition reciprocating blades with welded carbide tips at 6 TPI, for cutting wood, nailed wood and drywall. Blade width: 1".

A 3-pack of 6" Elite Series carbide-tipped reciprocating saw blades at 8 TPI, for demanding demolition and metal cutting.

A 3-pack of 12" demolition reciprocating blades with welded carbide tips at 6 TPI, for cutting wood with nails. The surface treatment is meant to strengthen the blade for demolition. Blade width: 1".

A single 12" Elite Series carbide-tipped reciprocating saw blade, 1" wide and .050" thick, at 8 TPI.

An 8" carbide grit reciprocating saw blade for cutting hard, abrasive materials.

A 25-pack of 2-1/8" bi-metal oscillating blades with a 3-sided cutting edge.

A 10-pack of 2-1/8" bi-metal oscillating blades with a 3-sided cutting edge.

A 10-pack of 2-1/2" precision-tooth oscillating blades in high-carbon steel for cutting wood. The universal fit works without an adapter on most oscillating tools.

A 3-pack of 2-1/2" precision-tooth oscillating blades in high-carbon steel for cutting wood. The universal fit works without an adapter on most oscillating tools.

A 25-pack of 1-1/4" bi-metal oscillating blades with a PlungePoint tip for starting plunge cuts in wood and other materials. DeWalt rates them at up to 7x the life when cutting nails.

A half-moon oscillating blade with diamond grit for removing tile grout. The universal fit works without an adapter on most oscillating tools. Blade width: 3-5/8".

A 3-piece set of oscillating tool blades.

A 14" (356mm) 100-tooth carbide-tipped blade for cutting aluminum, with a 1" arbor. Built from hardened steel plate with extra-hard carbide teeth.

A 7-1/4" 48-tooth blade for cutting aluminum, with a 5/8" arbor.

A 7-1/4" (184mm) 60-tooth carbide-tipped blade for cutting aluminum, with a 5/8" arbor. Hardened steel plate and extra-hard carbide keep the cut clean.

A 5-3/8" (136mm) 30-tooth carbide-tipped blade for cutting aluminum, with a 20mm arbor. Laser-cut hardened steel plate and extra-hard carbide for a long edge life. Kerf: .059".

A 12" (305mm) 80-tooth carbide-tipped blade for cutting aluminum, with a 1" arbor. Hardened steel plate and extra-hard carbide keep the edge sharp. Kerf: .11".

A 5-pack of fleece dust bags for DeWalt dust extractors, so you can empty the tank quickly and efficiently.

A 5-pack of paper dust bags for DeWalt dust extractors, so you can empty the tank quickly and efficiently.

A 5-pack of disposable plastic liners for DeWalt dust extractors, for emptying the tank without releasing dust.

A 2-pack of replacement HEPA filters for the DWV010 and DWV012 dust extractors.

A 15-foot anti-static hose for DeWalt dust extractors. It helps prevent static shocks, and a universal quick connector attaches tools fast.

A 15 ft crushproof replacement hose for the DWV012 dust extractor with a universal quick connector, for drywall sanding and concrete grinding, cutting and drilling.

An accessory hose for the DWV010 dust extractor, 2-1/2" diameter.

A 35mm tool adapter for connecting dust extractor hoses to tool dust ports.

A 35mm rubber adapter that fits the DWV9000 universal connector for quick hookup to tool dust ports 1.37" to 1.50" (35-38mm) OD.